Just to emphasize where the processes start and stop, I've changed the 2nd process in this cause to have a different Layer Extruder and Infill Extruder than the other 2 processes the preview looks like this: You might not see any definite change in the preview. If you do a test print and see strange behavior (could be anything from temperatures randomly changing to the wrong extruder printing), you should consider making note of which settings you change in case you need to reverse the changes later.ħ) When you're ready, click the "Prepare to Print!" button here you would keep all 3 processes selected and click "OK." NOTE: Changing certain settings may cause a conflict with other settings. In our example, since process 2 stopped at 26mm, process 3 will start at 26mm and simply finish the print:Ħ) Now, go into your processes and change the various speeds, infill percentages, or layer height. When you reach the last process, you'll simply un-check the "Stop printing at height." box and put the previous process' stopping height as the start height. Once you've calculated this, you can click the OK button to apply this to the 1st process.Ĥ) Do the same for the second process, except this time you will need to tell it to start at 9mm and stop at whatever height from the bottom of the model to the top of the flower we have found that 26mm from the base of the model is a good stopping point for the 2nd process:ĥ) Do this for any additional processes, but in our example, there are only 3 processes. For the example model above, we've found that 9mm is a good stopping point for the first process and starting point for the 2nd: You'll want to measure your model before hand to know at what height in millimeters you want the first process to stop and when you want the second process to start. Do not edit the settings of your 2nd process before adding your 3rd process ("3rd" based on the example above you may have more than 3 or only 2, all depending on your model).ģ) Now that all processes are created, go to the first one, double click it, and look at the settings to the "Advanced" tab. Therefore, if you set your settings correctly in "Process 1," subsequently added processes will mirror those settings.
![simplify 3d first layer height simplify 3d first layer height](https://i.redd.it/frn2ovxpjvgx.png)
Simplif圓D will create processes based on the last settings that you've made. This will be your standard for adjusting any additional processes for your model (there is a reason for this, which will be explained in step 6 below).Ģ) Click the "Add" button under the process section in Simplif圓D how ever many time you need to create additional processes.
#SIMPLIFY 3D FIRST LAYER HEIGHT HOW TO#
How to Set the Height of Multiple Processesġ) You'll first want to just start with one process and get it completely set up how you would normally print the entire first lower section to be. While Process 1 and Process 3 could remain relatively the same, Process 2 may be set to print slower so that the other two to ensures that you get better details with the flowering detail.
![simplify 3d first layer height simplify 3d first layer height](https://i.all3dp.com/wp-content/uploads/2021/02/04130625/gaps-in-top-layers-are-just-one-of-many-types-of-g-simplify3d-210113.jpg)
( Model is "Flower Box 2" (rosetteboxv2.stl) and was designed by Rob Keers, user "braveheart", published 12.04.15)Īs you can see from the photo, you could divide this model into 3 processes. By having a process that slows down the printing speed, increased the infill, or even lowers the primary layer height at specific points of your print, you can make certain areas of the part have improved quality. Simply put, multiple processes allow you to change certain settings at different heights of the print. This article is for those who use Simplif圓D and have print quality issues at the same area of a part every time they print it.
#SIMPLIFY 3D FIRST LAYER HEIGHT SOFTWARE#
Solution home Creatr HS (XL) 3D Printer Software - Simplif圓D Simplif圓D - How to Use Multiple Processes to Get Better Print Quality